SmartDup
MODEL VP-8220
Installation Manual
SmartDup VP-8220 Operation Manu
SmartDup VP-8220 Package Including:
1. Duplicator Converter.
2. CD-ROM Box (VP-6020) x 2
3. AC/DC Power Adaptor (Universal Type +90 ~ +250VAC)
Features:
1. One to one Stand-Alone IDE CD Duplicator.
2. Auto duplication & Easy operation without any push bottom.
3. Fastest CD Duplicator up to 24x speed (ViPowER is the only factory that
manufactures it today!)
4. Auto Detects CD-R or CD-RW media's acceptable maximum writing speed and
minimum writing time.
5. Upgrade through Internet, or upgrade via CD-ROM.
6. High Performance with Low cost & easy installation. No additional H/W or S/W
required.
7. External Power supply.
8. Supports Buffer Under Run.
9. Capable of connecting to your Desktop/ Notebook via Fire Wire/ USB/ PCMCIA/
Card Bus cable. (See option Desktop Interface)
10. Support Formats: Audio CD (CD-DA), CD-ROM, CD-XA (Photo & Video CD),
CD-Digital, CD-Bridge, CD-Extra, Video CD & CD-Text.
11. Automatically detects/ Erases/ Re-writes/ Copies.
12. Compatible with most well known CD-RW & CD-ROM Devices.
13. User friendly with LED display function.
14. Buzzer to alert user.
Install Steps:
1. Install CDR-W Writer & CD-ROM Driver in each CD-ROM box. Must put rubber
stand on each CD-ROM box.
2. CD-ROM Driver on top & CDR or CDR-W Writer on the bottom.
3. Plug in Duplicator Converter in both CD-ROM box connectors.
4. Plug in Power Cable in Duplicator Converter.
5. Plug in Power Cord to AC Power source (+90 ~ +250VAC).
6. LED Display on top of Duplicator Converter.
7. Dip Switch on Top of Right hand side. To adjust duplicator function.
8. Rock Switch on Right hand side, power switch. Normally in ON position
Function Setting
4: Test & Copy 5: Test Only 6: Copy Only 7: Auto Mode
(Erase & Copy)
High Speed
(Maximum)
3: Erase Only 2: 1x Copy
(Minimum)
1: Upgrade 0: Reserved
Firmware
Low Speed
(4x)
SmartDup VP-8220 Operation Manu
1
H1 (Upgrade firm-ware): DIP SW 3 4 at ON position, 1 2 at OFF position---
If you adjust DIP SW to L1, all operation step same as above, the Recording
Speed will drop to 4x only.
1 1. Turn Rock Switch to position (CD Duplicator). LED will show version number.
Power-On: display firmware version number. (Buzzer 0.5s X1)
ex:
1-2. Than LED display showing: from 00,11, 22, 33, ......88, 99
1-3. Duplicator will chk itself & get ready.
Self-Test: Only one segment is running and display "rd" (ready)
1-4. Please insert your new Firm-Ware CD title into your CD-ROM Drives,
operation step as below:
1 4 2. Switch your power switch to (PC interface)
1-4-3. Please check Optional Step (page 10)
1-4-4. Burning new Firm-Ware into your CD-R or CDR-W media.
1-5. LED Display showing final counts down. Than LED showing H1 or L1.
Count Down: After drives & discs ready in current mode, wait for
5 seconds. (Buzzer 0.2s X1)
ex:
1-6. SmartDup will upgrade automatically.
1-7. After Upgrade success, Buzzer will Beep & eject Firm-Ware Title. LED
showing 00.
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)
1-8. Showing new firmware version.
1-8-1. If fail, LED will showing: Er & eject CD-R Media, Buzzer will Beep also.
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)
2
SmartDup VP-8220 Operation Manu
H2(1xCopy) DIP SW 2 4 at ON position, 1 3 at OFF position---------------
L2(1xCopy) DIP SW 2 at ON position, 1 3 4 at OFF position----------------
1xCopy Speed (H2 or L2) or CD-RW writer minimum writing speed.
2-1. Turn Rock Switch to position (CD Duplicator). LED will show version
number.
Power-On: display firmware version number. (Buzzer 0.5s X1)
ex:
2-2. Than LED display showing: from 00,11, 22, 33, ......88, 99
2-3. Duplicator will chk itself & get ready.
Self-Test: Only one segment is running and display "rd" (ready)
2-4. SmartDup ready, please insert your CD title into your CD-ROM Drive &
Blank CD-R or CD-RW Media in CD-RW Writer.
2-5. LED Display showing final counts down, than LED showing H2 or L2.
Count Down: After drives & discs ready in current mode, wait for
5 seconds. (Buzzer 0.2s X1)
ex:
or
2-6. LED Display showing CD-R or CD-RW Media writing speed or depend on
CD-RW writer minimum writing speed.
CD-R Maximum Writing Speed:
2-7. LED Display showing CD-R or CD-RW Media minimum writing time
remaining.
Remain minutes: During Test or Copy mode. Flash every second
ex:
or
2-8. After Upgrade success, Buzzer will Beep & eject CD-R media. LED
showing 00.
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)
2-8-1. If fail, LED will showing: Er & eject CD-R Media, Buzzer will Beep also.
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)
SmartDup VP-8220 Operation Manu
3
H3 (Erase Only): DIP SW 2 3 4 at ON position, DIP SW 1 at OFF position--
L3 (Erase Only): DIP SW 2 3 at ON position, DIP SW 1 4 at OFF position---
This function for RW Media with Data inside, operation steps same as H3,
Erase speed drop to 4x only.
3-1. Turn Rock Switch to position (CD Duplicator). LED will show version
number.
Power-On: display firmware version number. (Buzzer 0.5s X1)
ex:
3-2. Than LED display showing: from 00,11, 22, 33, ......88, 99
3-3. Duplicator will chk itself & get ready.
Self-Test: Only one segment is running and display "rd" (ready)
3-4. SmartDup ready, please insert your CD title into your CD-RW Media in
CD-RW Writer.
Count Down: After drives & discs ready in current mode, wait for
5 seconds. (Buzzer 0.2s X1)
ex:
or
3-5. LED Display showing final counts down, than LED showing H3 or L3.
3-6. Start Erasing.
Erasing:
3-7. After Erased success, Buzzer will Beep & eject CD-RW media. LED
showing 00.
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)
3-7-1. If fail, LED will showing: Er & eject CD-R Media, Buzzer will Beep also.
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)
4
SmartDup VP-8220 Operation Manu
H4(Test & Copy Mode) DIP SW 1 4 at ON position, 2 3 at OFF position-----
L4(Test & Copy Mode) DIP SW 1 at ON position, 2 3 4 at OFF position-----
If you adjust DIP SW to L4, all operation steps same as H4, the Recording
Speed will drop to 4x only.
Please make sure CD-R or CD-RW media is blank.
4-1.Turn Rock Switch to position (CD Duplicator). LED will show version
number.
Power-On: display firmware version number. (Buzzer 0.5s X1)
ex:
4-2. Than LED display showing: from 00,11, 22, 33, ......88, 99
4-3. Duplicator will chk itself & get ready.
Self-Test: Only one segment is running and display "rd" (ready)
4-4. SmartDup ready, please insert your CD title into your CD-ROM Drive &
Blank CD-R or CD-RW Media in CD-RW Writer.
4-5. LED Display showing final counts down, than LED showing H4 or L4.
Count Down: After drives & discs ready in current mode, wait for
5 seconds. (Buzzer 0.2s X1)
ex:
or
4-6. LED Display showing CD-R or CD-RW Media maximum writing speed.
CD-R Maximum Writing Speed:
or
or
4-7. LED Display showing CD-R or CD-RW Media minimum writing time remaining.
Remain minutes: During Test or Copy mode. Flash every second
ex:
or
or
4-8. After Test success, Buzzer Beep & LED showing 00. Than re-start Copy.
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)
4-8-1. If fail, LED will show: Er & eject CD-R Media also.
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)
4-9. LED Display showing CD-R or CD-RW Media maximum writing speed.
CD-R Maximum Writing Speed:
or
or
4-10. LED Display showing CD-R or CD-RW Media minimum writing time
remaining.
Remain minutes: During Test or Copy mode. Flash every second
ex:
or
or
4-11. After Copy success, Buzzer will Beep & eject CD-R media. LED showing 00
.
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)
4-11-1. If fail, LED will showing: Er & eject CD-R Media, Buzzer will Beep also
.
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)
SmartDup VP-8220 Operation Manu
5
H5 (Test Only): DIP SW 1 3 4 at ON position, 2 at OFF position--------------
L5 (Test Only): DIP SW 1 3 at ON position, 2 4 at OFF position---------------
If you adjust DIP SW to L5, all operation steps same as H5, the Recording
Speed will drop to 4x only.
5-1. Turn Rock Switch to position (CD Duplicator). LED will show version
number.
Power-On: display firmware version number. (Buzzer 0.5s X1)
ex:
5-2. Than LED display showing: from 00,11, 22, 33, ......88, 99
5-3. Duplicator will chk itself & get ready.
Self-Test: Only one segment is running and display "rd" (ready)
5-4. SmartDup ready, please insert your CD title into your CD-ROM Drive &
Blank CD-R or CD-RW Media in CD-RW Writer.
5-5. LED Display showing final counts down, than LED showing H5 or L5.
Count Down: After drives & discs ready in current mode, wait for
5 seconds. (Buzzer 0.2s X1)
ex:
or
5-5-1. If put in CD-RW Media with Data; CD-RW will eject & show Er.
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)
5-6. LED Display showing CD-R or CD-RW Media maximum writing speed.
CD-R Maximum Writing Speed:
or
or
5-7. LED Display showing CD-R or CD-RW Media minimum writing time
remaining.
Remain minutes: During Test or Copy mode. Flash every second
ex:
or
or
5-8. After Testing success, Buzzer will Beep & eject CD-R media. LED showing
00.
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)
5-8-1. If fail, LED will show: Er & eject CD-R Media also.
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)
6
SmartDup VP-8220 Operation Manu
H6 (Copy Only): DIP SW 1 2 4 at ON position, 3 at OFF position-------------
L6 (Copy Only): DIP SW 1 2 at ON position, 3 4 at OFF position--------------
If you adjust DIP SW to L6, all operation steps same as H6, the Recording
Speed will drop to 4x only.
6-1. Turn Rock Switch to position (CD Duplicator). LED will show version
number.
Power-On: display firmware version number. (Buzzer 0.5s X1)
ex:
6-2. Than LED display showing: from 00,11, 22, 33, ......88, 99
6-3. Duplicator will chk itself & get ready.
Self-Test: Only one segment is running and display "rd" (ready)
6-4. SmartDup ready, please inserts your CD title into your CD-ROM Drive &
Blank CD-R or CD-RW Media in CD-RW Writer.
6-5. LED Display showing final counts down, than LED showing H6 or L6.
Count Down: After drives & discs ready in current mode, wait for
5 seconds. (Buzzer 0.2s X1)
ex:
or
6-5-1. If put in CD-RW Media with Data, CD-RW will eject & show Er.
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)
6-6. LED Display showing CD-R or CD-RW Media maximum writing speed.
CD-R Maximum Writing Speed:
or
or
6-7. LED Display showing CD-R or CD-RW Media minimum writing time
remaining.
Remain minutes: During Test or Copy mode. Flash every second
ex:
or
or
6-8. After writing success, Buzzer will Beep & eject CD-R media. LED showing
00.
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)
6-8-1. If fail, LED will show: Er & eject CD-R Media also.
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)
SmartDup VP-8220 Operation Manu
7
H7(High Speed Auto Mode):DIP SW always at ON position------------------
L7(Low Speed Auto Mode):DIP SW 1 2 3 at ON position, 4 at OFF position-
If you adjust DIP SW to L7, all operation steps same as H7, the Recording
Speed will drop to 4x only.
7-1. Turn Rock Switch to position (CD Duplicator). LED will show version
number.
Power-On: display firmware version number. (Buzzer 0.5s X1)
ex:
7-2. Than LED display showing: from 00,11, 22, 33, ......88, 99
7-3. Duplicator will chk itself & get ready.
Self-Test: Only one segment is running and display "rd" (ready)
7-4. SmartDup ready, please insert your CD title into your CD-ROM Drive &
Blank CD-R or CD-RW Media in CD-RW Writer.
7-5. LED Display showing final counts down, than LED showing H7 or L7.
Count Down: After drives & discs ready in current mode, wait for
5 seconds. (Buzzer 0.2s X1)
ex:
or
7-5-1. If insert CD-R Media with Data inside, it will eject & showing Er & if insert
CD-RW media with data, LED display will showing Er & CA, RW driver will
eject RW media.
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)
7-5-2. If put RW tray in, than LED will show final count down & Erasing RW.
Count Down: After drives & discs ready in current mode, wait for
5 seconds. (Buzzer 0.2s X1)
ex:
or
7-5-3.
Erasing:
7-6. LED Display showing CD-R or CD-RW Media maximum writing speed.
CD-R Maximum Writing Speed:
or
or
7-7. LED Display showing CD-R or CD-RW Media minimum writing time
remaining.
Remain minutes: During Test or Copy mode. Flash every second
ex:
or
or
7-8. After writing success, Buzzer will Beep & eject CD-R media. LED showing 00.
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)
7-8-1. If fail, LED will show: Er & eject CD-R Media also.
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)
8
SmartDup VP-8220 Operation Manu
SmartDup VP-8220 Optional interface:
1. VP-9006: PCMCIA to IDE cable with 36 pin connector.
2. VP-9007: CardBus to IDE cable with 36 pin connector.
3. VP-9008: USB 1.1 to IDE cable with 36 pin connector.
4. VP-9009: FireWire IEEE 1394 to IDE cable with 36 pin connector.
5. VP-9208: USB 2.0 to IDE cable with 36 pin connector.
Features:
1. External CD-RW writer.
2. Back Up your own Data/ Audio/ Video from HDD/ MO/ LS120/ ZIP... through your
PC/ Note Book/ MAC to your SmartDup
HardWare minimum Request:
1. PCMCIA Type or Type Slot, USB port or FireWire.
2. Pentium 400 Mhz or Greater.
3. 64 MB RAM.
4. USB 2.0 version needs USB2.0 Host Card (VP-9628) or other compatible USB
2.0 Host Card.
5. FireWire 1394 IEEE need FireWire 1394 IEEE Host Card (VP-9609) or other
compatible 1394 IEEE Host Card.
6. CardBus to USB 2.0: Please make sure your NoteBook PCMCIA Slot support
CardBus (VP-9728) or other compatible Card.
7. CardBus to FireWire 1394 IEEE: Please make sure your NoteBook PCMCIA Slot
support CardBus (VP-9709) or other compatible Card.
8. One of the Following Operating System:
(1.) Win 98SE/ 2000/ ME/ MAC os 9.0x for USB 1.1 version.
(2.) Win 98SE/ 2000/ ME/ MAC os 9.0x for USB 2.0 version
(3.) Win 98SE/ 2000/ ME/ MAC os 9.0x for FireWire.
(4.) Win 98SE/ 2000/ ME for CardBus.
(5.) Win 98SE/ 2000/ ME for PCMCIA.
Driver Software request:
1. USB 1.1 version interface: Need install USB drive software under Win 98SE &
No Need install any USB drive software under Win ME/ Win 2000 & MAC os 9.0.
2. USB 2.0 version interface: Need install USB drive software under Win 98SE &
No Need install any USB drive software under Win ME/ Win 2000 & MAC os X.
3. FireWire IEEE 1394 Interface: No Need install any drive software under Win
98SE/ ME/ Win 2000 & MAC os 9.0.
4. CardBus Interface: Need install CardBus drive software under Win 98SE/ ME/
Win 2000.
5.PCMCIA Interface: No Need install any drive software under Win 98SE/ ME/ Win
2000.
SmartDup VP-8220 Operation Manu
9
Install Steps:
1. Install CD-RW Writer & CD-ROM Driver in each CD-ROM box. Must put rubber
stand on each CD-ROM box.
2. CD-ROM Driver on top & CDR or CD-RW Writer on the bottom.
3. Plug in Duplicator Converter in both CD-ROM box connectors.
4. Plug in Power Cable in Duplicator Converter.
5. Plug in Power Cord to AC Power source (+90 ~ +250VAC).
6. 36 pin IDE cable connect between SmartDup & your PC or Note Book interface
port.
7. Turn your Power switch to (PC interface), LED Display will blinking.
8. Make sure install success.
9. You can start back-up your Data/ Audio/ Video.
Caution:
1. Make sure CD-RW burning software can recognize CD-RW writer.
2. Make sure your CD-R or CD-RW media acceptable maximum writing speed.
3. Maximum data transfer rate (byte/sec)
PCMCIA
600K
CardBus
600K
USB 1.1
600K
900K
900K
900K
900K
900K
USB 2.0
600K
FireWire
600K
4X
6X
900K
900K
900K
900K
8X
1200K
2000K
2000K
2000K
1200K
3600K
3600K
3600K
1200K
3600K
4800K
6000K
1200K
3600K
4800K
6000K
24X
32X
40X
4. CD-RW Driver Maximum Writing Speed through PC Interface:
(1.) PCMCIA: 8 x
(2.) CardBus: 16 x
(3.) USB 1.1 Version: 4 x
(4.) USB 2.0 Version: 20 x
(5.) FireWire IEEE 1394: 20 x
New Firm-Ware download:
1. Same as Install Step 1~ 8 at page 11.
3. Put CD-RW or CD-R media in to your CD-RW writer.
4. CD-RW writer as External CD-RW writer.
5. Start Copy New Firm-Ware to RW media.
6. Back to Page 3.
10
SmartDup VP-8220 Operation Manu
How to Up-Grade CD-ROM F irm-Ware
If you wish get best performance on your SmartDup.
Model number & Firm-Ware Version Number.
2. ViPowER Inc. CDR/RW Driver Approved List
Brand
Acer
Model Number
CRW1208A
CRW9420A
CRW9624A
CRW 1232A
CRW2040
4424
Note
Brand Model Number
Note
SeamLess Plextor
Plextor
PX-W1210A
PX-W1610A
7040A
AOpen
AOpen
AOpen
AOpen
BTC
BurnProof
Ricoh
JustLink
JustLink
Ricoh
Ricoh
Ricoh
SONY
SONY
SONY
SONY
SONY
7060A
7080A
MP7200A
CRX -100E
CRX -120E
CRX -140E
CRX -145E
CRX -160E
4416E
HP
8100i
HP
8200
HP
9100
HP
9200
HP
9300
Lite-On
Lite-On
Lite-On
Lite-On
Panasonic
Panasonic
Philips
Philips
Plextor
LTR-12101B
LTR-16101B
LTR-16102B
LTR-24102B
7585
BurnProof YAMAHA
BurnProof YAMAHA
BurnProof YAMAHA
BurnProof YAMAHA
TDK
8424E
8824E
2100E
CRD -BP1300P BurnProof
CRW54E
7586
TEAC
PCA460RW
CDD -4801
PX-W8432T
TEAC
CRW512EB
BurnProof
Sanyo
CRD -BP1400
BurnProof Sanyo
CRD -BP1500P BurnProof
3. Best Match (ViPowER will give several suggest for you reference).
4. Than you can get best performance on your SmartDup.
5. ViPowER will recommend several match, not only performance, but also easy to
purchase from any retail chain store near by you.
6. Do not up-grade by yourself, but you can ask your store up-grade for you.
7. If you wish up-grade by yourself, please make sure can up-grade success. If fail,
this CD-ROM driver can't use anymore. On the other hand, most of CD-ROM
manufacture will not take any responsibility, because up-grade fail.
SmartDup VP-8220 Operation Manu
11
8. You can ask your retail store to purchase any brand of CD-ROM driver, which
ViPowER supply or recommend.
9. CD-ROM Compatibility List
CD-RW ACER 52x Afreey 52x AOpen 52x ASUS 52x LITEON 52x TEAC 40x
8x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
12x
16x
20x
24x
Acer CD-ROM Model Number: CD-652P Version: ??
AOpen CD-ROM Model Number: CD-952E/TKU Version: C41
Asus CD-ROM Model Number: CD-S 950/A Version: 1.0D
AFreey CD-ROM Model Number: CD-2052E Version: V31
LiteOn CD-ROM Model Number: LTN-526S Version: YS0C
TEAC CD-ROM Model Number: CD-540E Version: 3.0A
Or you can send e-mail to us.
Printed on recycled paper.
|